Releases: andrivet/ADVi3pp
Releases · andrivet/ADVi3pp
ADVi3++ version 5.8.0
ab72185
This release has major fixes. In particular, following messages in this community, I found that the X-Twist compensation feature was completely broken. There were also issues with homing (G28), and incorrect flow rate during Extruder Tuning.
The complete list of changes is the following:
- #344 - Leveling state is not restored after homing
- #343 - X-Twist compensation is broken
- #342 - Synchronise sources with Marlin 2.1.2.2 (prepare Input Shaping for version 6.0)
- #337 - Manual Leveling does not check bed temperature and does not home
- #335 - Tuning Extruder: the flowrate is incorrect
- #334 - Extruder tuning - measurement image missing 5.7.x
ADVi3++ version 5.7.0
This release has important fixes and new features. In particular, it now supports a BLTouch sensor with Mark II printers. See the announcement for more information.
The complete list of changes is the following:
- #332 - SD card sorting is not working as expected bug
- #329 - Add a way to cancel Load and Unload filament enhancement
- #327 - For Mark II printers, select by default the Mark II offsets for the probe enhancement
- #326 - Synchronise sources with Marlin 2.1.2 enhancement
- #322 - Save the last temperature used to Load/Unload and restore it on boot enhancement
- #319 - Use Touch Switch Mode (SW) for BLTouch enhancement
- #315 - Beep in Preheat when the target temperature is achieved enhancement
- #314 - Apply the setting under Settings / Beeper / Beep duration to M300 without P argument enhancement
- #262 - Add BLTouch support for i3 plus Mark II enhancement
- #115 - Allow Temp Change during filament change enhancement
ADVi3++ version 5.6.0
ADVi3++ version 5.5.1
ADVi3++ version 5.5.0
- #318 - Thermal runaway error is not always displayed on the LCD screen
- #317 - G-Code M114 response breaks Octolapse
- #313 - Cancel automatic leveling
- #312 - Detect and prevent bounces
- #311 - Restore Z-offset in Sensor Settings
- #310 - Add steps in BLTouch Tuning for cases when the BLTouch is blinking red
- #308 - Update description of Print Settings pane
- #307 - Versions over 5.0.3 having issues accessing SD card files
- #306 - Fast probing with BLTouch
- #293 - BLTouch - warning on transposed black and white wires
- #296 - Manual jog controls disturb homing function, triggering "Homing failed" hardware error
- #294 - If print menu is accessed while printer is moving, it shows as if it's printing
- #267 - Live Flow Tuning
- #238 - M851 should accept all offset arguments, not just Z offset
- #153 - Graph as default view or GCode to show the graph view
ADVi3++ version 5.4.2
ADVi3++ version 5.4.1
ADVi3++ version 5.4.0
- #291 - When pressing on a move button, it continues for a while after the button is released
- #290 - Avoid homing when not necessary
- #289 - Travel movements during manual bed levelling significantly slower than earlier versions
- #288 - Inversion of black and white BLTouch wires not detected
- #287 - Warn if manual bed leveling is attempted while extruder is hot
- #285 - Show what triggered a hardware error
- #284 - LCD stuck dim when hardware error detected
- #279 - Enhance the beeping feature
- #277 - Raise extruder during Tuning / Extruder
- #274 - Enhanced motion during filament load
- #246 - Skew compensation implementation
- #177 - Cancel e-steps tuning